Jacob-
Thanks for the reply. And thanks for confirming no change to IR sensor data handling. OK… time for some maintenance.
re: dead man switch… I understand your design philosophy. After a little more thought I realized that Artisan already supports the Bullet. That opens the door for a hack to automate the dead-man switch response via USB port and defeating the whole process. Guess I talked myself out of my feature request!
Bruce
Hi Wayne-
Yes, I thought I had V2, but after an exchange with Sweet Maria’s I learned I have V1.5.
When I asked about it they were alarmed I might have found something on their site that said V2. They’ve apparently avoided any reference to Bullet Vxx designations. However, it was on the Aillio site I’d seen reference to V2 as the current production configuration… that’s what seeded the misunderstanding on my part. Now I’m waiting for the new power board like everyone else (though I’m thinking about the 240 VAC board with a step-up transformer… depends on board availability).
Bruce
From my understanding the release of v1.5 was when they changed the IR sensor to remove the glass cover and have “air blowing on the sensor”. My understanding was that this improvement would remove the need to clean the IR sensor as was occasionally necessary to do in the v1.0 units.
Are we now hearing that we still need to clean the sensor in a v1.5 unit? If so, then I need to add that back-in to my maintenance routine for the Bullet.
Yes, you will still need to clean the sensor, and for larger batches remove stray coffee beans that may get stuck there.
The latest version of the manual does not mention cleaning the surface of the v1.5 IR sensor. It only speaks to cleaning the window that was in front of the IR sensor on the v1.0 units.
So, I’d like to hear from Jacob as to the interval, recommended cleaning solution and/or technique to properly clean the surface of the IR sensor. I probably have as many coffee cleaners and solvents as the next “coffee geek”. But, we have no guidance from the manufacturer on this particular maintenance for the v1.5 IR sensor. When it comes to cleaning something as important as this sensor, I think it prudent to hear what Aillio specifically says on the subject.
@jacob spoke to this already here: IBTS... To clean or not to clean? That is the question - #3 by jacob
@yakster, that’s exactly what I wanted to see and thanks for pointing me to that post! 
It was being discussed before I was a Bullet owner and participating here.
I’d previously taken a peek at my IR sensor when a couple of people here reported beans lodging inside the sensor area of the v1.5. Using my Depstech Endoscope, my sensor’s area was free of debris and the sensor surface was clear.
I’ll add that sensor inspection to my maintenance repertoire and now know the recommended cleaning too. Hopefully, they will add that when they do a future update of the Bullet manual. I have my own edited and notated version and will add this process to it in the maintenance section.
I just finished cleaning the IRTS and have discovered a huge admiration for those who have installed that mod in their V1 Bullet. That was not a trivial task. For my part I backed out of getting full access to the sensor when I spent an hour looking for a lost screw and settled for using the alcohol-soaked swab through the opening. There are things best left untouched till someone holds a gun to your head!
We have more spring winds tomorrow and the next day, so it’ll be a couple days before I can roast and see if there was any change in measured IR temp at 1st/2nd crack. Frankly I didn’t see anything on the swab, so if it changes I expect it’ll be minor.
Bruce
Good to know what you observed. Doesn’t appear that the sensor needed cleaning and I’m curious how many roasts you have on your Bullet? Cleaning that sensor may be something that only needs done “once in a blue moon” which would be fine with me. 
As I recall I saw 40 roasts had been recorded. I received the Bullet in the 2nd half of Jan this year.
I recall BlackStripeCoffee mentioning the need to clean the sensor every 20 kg (?) of roasting (they roast a lot of coffee!), so I was watching for some indication of a change. The change was sudden, so I expected something significant… chaff particle? bean fragment? No such luck.
Bruce
Thanks for that info Bruce! 
Got frustrated with windy weather here in SE Arizona, so I roasted 4 batches anyway. I found the IBTS offset at Yellow point & FC persist. My issue was/is apparently not a dirty lens on the IBTS. This result isn’t really a surprise since (unlike BlackStripeCoffe’s experience) the swab seemed to pick up nothing from the surface of the lens.
So I’ll just deal with the offset by dumping the beans earlier 12°F to 15°F (there seems to be a slope to the error, so it’s not just an offset). When I hear about some other explanation/approach on this forum I’ll adjust.
Btw, I believe this started when I updated from f/w 507 to f/w 508 then 512.
Bruce
On the 64 Bit version, the recipe never worked, at the end of the roast I didn’t have manual control over the roaster, I pressed the PRS button and nothing happened, I had to unplugged the roaster and start another roast to allow the fans to work. after the end of the roast alarm, Roast Time stop recording.
This is frankly one reason that I’m avoiding use of the latest alpha or beta releases of anything for the Bullet. I’m as excited as anyone else to use new features, but what I don’t need is to introduce new problems with the roaster while I’m adjusting to this new device.
In many other software related things I have been that “guinea-pig” for Devs many times. But, when it comes to my coffee roasting, I like stable software and predictable results from the device so that I’m the one interjecting the change via tweaking roasts.
Jacob,
I can not find RT 2.3.1 beta download. I am 2.2.0 and the update button does not update even though it tells me there is an update available. Where can I find the update?
Thank you
Alex, they keep all the releases on the site below (ordered by Operating System type).
Thank you
Or you can get them directly from the Aillio website
https://downloads.aillio.com/roastime-downloads/windows-beta-release-download
Is anyone else having the beta RT crash on them about 1 out of every 5 roasts in recipe mode? For me it freezes up either in preheat or mid-roast. When it happens, the roasts are manageable manually but all recording and automated controls are lost.
Is anyone else having the beta RT crash on them about 1 out of every 5 roasts in recipe mode? For me it freezes up either in preheat or mid-roast. When it happens, the roasts are manageable manually but all recording and automated controls are lost.
I don’t use Recipes, but if you’re using RT 2.3.0 beta, you may want to try RT 2.3.1 beta. Fixed my issues with RT 2.3.0 beta, though crashing wasn’t one of them.
Bruce